Close

## What happens when two continental plates slide past each other?

When oceanic or continental plates slide past each other in opposite directions, or move in the same direction but at different speeds, a transform fault boundary is formed. No new crust is created or subducted, and no volcanoes form, but earthquakes occur along the fault.

## What is it called when two tectonic plates move away from each other?

A divergent boundary occurs when two tectonic plates move away from each other. Along these boundaries, earthquakes are common and magma (molten rock) rises from the Earth’s mantle to the surface, solidifying to create new oceanic crust. When two plates come together, it is known as a convergent boundary.

READ:   What would happen if Earth did not have an atmosphere?

## What happens at a plate boundary where two plates are moving towards from each other?

Convergent boundaries occur where two plates slide towards each other to form either a subduction zone (if one plate, normally an oceanic plate moves underneath the other) or a continental collision. Transform boundaries occur where two lithospheric plates slide past each other along transform faults.

## What type of plate boundary is present between A and C?

Answer. It’s a convergent plate boundary.

## What do you think may happen to the leading edge of plate A as it continues to move downward Why?

What do you think will happen to the leading edge of Plate A as it continues to move downward? ANSWER: The leading edge of Plate A will start to melt because the temperature beneath the crust (mantle) is higher.

## What happens if oceanic plate continues to move downward?

The leading edge of oceanic plate will melt if it continues to move downward because the temperature through the crust is higher.

## What happens to the plate when they are pushed to the opposite ends?

Answer. Answer: When the strips of clay are pushed from opposite ends then they buckled upwards a little bit which raises the surface a little bit forming like a mountain on the land. Explanation: The pushing of the clay from the contrary sides is an environmental change which results in the development of the plates.

## What happened to the towels as they pushed from the opposite side?

Answer. Answer: When you pushed the towel towards each other, it will buckled up. If the towel represents the Earth’s lithosphere, it will formed mountain ranges as the towel buckled up.

## What happened to the creamy white center of the two broken biscuit as you pressed?

Answer. Answer: The cream will slowly come out to every edge of the biscuit.

## What happened to the modeling clay when push?

Answer: if modeling clay was pushed it will change the size and shape.

## What happened if press a clay?

Answer: if you will press a clay the clay will mold depends what shape or texture that you use. because clay is a stiff, sticky fine-grained earth, typically yellow, red, or bluish-gray in color and often forming an impermeable layer in the soil.

READ:   What is hybrid seed production?

## What happened to dough when pressed?

Answer. A lump of dough on A lump of dough on a plate. Pressing it down with your hands . The Action of Force results in Change in Shape because when you press a lump of dough in downward direction with your hands then its shape will be changed but there will be no change in its state of motion.

## What happened to the plastic ruler when bent?

What happens when plastic ruler bent? Answer. When you bend the plastic ruler, too much pressure is placed upon the part that is bent, causing the ruler to break and split into several pieces, it is the property brittleness in matter.

## What will happen to metal spoon when bent?

Answer. – When the metal spoon was bent, it changed its physical appearance and the spoon appeared to be bent. This process is often referred to as undergoing physical change since only the characteristics or physical appearance of an object change. It is also possible to revert back the object to its original form.

## What happen to the materials when bent?

Answer Expert Verified When solid materials are bent, pressed, or hammered experience a physical change. Examples of physical change include changes in size, shape, and state. The processes that cause physical changes are cutting, bending, dissolving, freezing, boiling, and melting.

## Is it important to know if the material can be bent pressed hammered or cut?

Was there a new materials formed when solid materials are bent, pressed, hammered and cut? No. when materials are bent, pressed, etc., those are just physical changes and the materials may change.

## Why can we bend the ruler?

You can bend a ruler in any direction. The ruler is much thicker along its breadth than height so you are bending much more material. Same force is trying to bend about 20 times as much material. and because of its elasticity.

## What happens when you bend a paperclip?

It undergoes plastic deformation as the discontinuities in the crystal structure of the metal slip and rearrange. After repeated bending, the discontinuities become so tangled that they can’t slip any more – the metal is said to work harden.

READ:   Are rattlesnakes born alive?

## How will you change the size and shape of plastic ruler?

We can change the size and shape of plastic ruler by. (bending, pressing).

## What happened to the materials when bent paper clip?

Answer: Bending also puts energy into the material, causing it to get warmer. In this experiment, typically the 180 degree bend breaks the paper clip in less than half the number of bends due to the greater stress on the bending point.

## Can you harden a paperclip?

Firstly, bending the paper clip back and forth produces an effect on the metal known as work hardening. As you do more work on the metal, it becomes harder and more brittle. Eventually, it will become so brittle that it will snap, and this is why you can snap a cheap spoon simply by bending it back and forth.

## Why can you bend a paperclip only a few times before it breaks?

As defects accumulate, the metal gets harder and stronger, more difficult to bend. Cracks form, leading to a “fatigue” failure. Typically the 180-degree bend breaks the paper clip in less than half the number of bends due to the greater stress on the bending point.

## What happened to the copper wire when bent?

Answer: If a wire is bent to form loops, it acts as an inductor. Each loop of the inductor exhibits a capacitance effect with the next loop. So, explicitly, the resistance of the wire doesn’t change when you bend it.

## What change happened to electric wire when bent?

If a wire is bent to form loops, it acts as an inductor. Each loop of the inductor exhibits a capacitance effect with the next loop. That is, a bent wire will exhibit all three properties: inductance, resistance and capacitance. So, explicitly, the resistance of the wire doesn’t change when you bend it.